← Back to Knowledge Base

    ★ .22LR Knowledge Base

    Stocks, Chassis, Torque, and Bedding

    Building a Long Gong rifle that returns to zero

    By Joe Eldridge

    © Property of Texas Long Gong

    You are welcome to share a link to this article or link back to it from your own site. Please do not copy, republish, or rehost the article in whole or in part on another site. Backlinks are encouraged; lift-and-shift is not permitted.

    There is a moment, somewhere around your fiftieth or hundredth round downrange, when you stop wondering whether your rifle can hit the gong and start wondering whether you can. That moment is the goal. Everything we do at the workbench — picking a stock or a chassis, setting action screw torque, deciding whether to bed an action or run pillars — exists to get you there faster and keep you there longer.

    This article walks through the platform decisions that shape how a Long Gong rifle shoots: stocks versus chassis, how to tune each, why action screw torque matters more than most shooters realize, and what bedding and pillars actually do for accuracy. None of this is exotic. All of it is repeatable. By the end you should have a clear picture of how to set up your rifle so that the variable in the equation is wind reading and trigger discipline — not whether the barreled action sat in the same place it did yesterday.

    Stocks vs. Chassis: What You're Really Choosing Between

    A stock and a chassis serve the same fundamental purpose: hold the barreled action in a fixed, repeatable position and give the shooter a stable interface to the rifle. They go about it in very different ways, and each has tradeoffs that matter for a 300-yard rimfire game.

    Traditional Stocks

    A stock is a one-piece body — wood, laminate, fiberglass, or carbon composite — machined or molded to accept the action. The barreled action drops into an inletted channel and is held down by action screws that thread into the receiver through the stock and bottom metal.

    Pros:

    • Weight. A good laminate or composite stock is usually lighter than a comparable chassis, which matters if you carry your rifle to the line, hunt with it, or shoot positional stages.
    • Feel. Wood and composite warm in your hand. They dampen vibration. For shooters who came up on traditional sporters, a stock feels right in a way that's hard to articulate but easy to recognize.
    • Cost. Factory stocks are usually included with the rifle. Upgraded laminate or fiberglass stocks (Boyds, Manners, McMillan, Foundation) cost less than most chassis at comparable quality tiers.
    • Bedability. A well-built stock is a blank canvas for bedding work. Done right, a bedded stock can match or beat a chassis for raw mechanical precision.

    Cons:

    • Wood moves. Humidity, temperature, and time all change the dimensions of a wood stock, even laminated stocks to a lesser degree. That movement can shift point of impact between range trips.
    • Limited adjustability. Most stocks have a fixed length of pull, fixed comb height, and no built-in cant or rail interfaces. Adjustable cheek pieces and spacer systems help, but you're still working within the geometry the stock was molded with.
    • Inletting variance. Factory inletting is rarely perfect. Voids, high spots, and uneven contact between the action and the stock are the rule, not the exception, which is why bedding exists.

    Chassis Systems

    A chassis is typically a CNC-machined aluminum (sometimes magnesium or polymer-skinned) skeleton that the barreled action mounts to via a V-block, recoil lug interface, or direct bolt-down. The buttstock, forend, grip, and accessories all bolt to the chassis as modular components.

    Pros:

    • Rigidity and repeatability. Aluminum doesn't compress, swell, or warp the way wood does. The interface between action and chassis is engineered to be the same on round one and round one thousand.
    • Adjustability. Length of pull, comb height, cheek piece position, grip angle, butt hook, bag rider, ARCA rail, M-LOK accessories — almost every dimension is user-tunable. For positional shooting and for shooters who share a rifle, that adjustability is huge.
    • Modularity. Want to swap a Vudoo into a chassis inletted for a Remington 700 pattern? Same with a Bergara B14R. If the action shares the same footprint, it's usually a barreled-action swap and a couple of bolts. The chassis becomes a platform you build around.
    • No bedding required (usually). A well-machined V-block or precision-inlet chassis is designed so that the action drops in and seats consistently without epoxy work.

    Cons:

    • Weight. Most full-feature chassis run heavier than the equivalent stock. For Long Gong this is often a feature, not a bug — weight steadies the rifle — but it's worth noting.
    • Cost. Quality chassis from MDT, KRG, MPA, Foundation, XLR, and others typically run from a few hundred to well over a thousand dollars. That's on top of the rifle.
    • Feel. Aluminum is cold, hard, and unforgiving. Some shooters never warm up to it. Skinned chassis like the KRG Bravo soften this, but it's still not wood.
    • Action fit matters. A chassis with a sloppy V-block or imprecise inlet can shoot worse than a bedded stock. The mechanical engineering of the chassis is doing the work bedding would otherwise do, and not all chassis do it equally well.

    Which One for Long Gong?

    There is no universal answer, and the gong doesn't care what your rifle is wearing. We have shooters running everything from factory CZ 457 stocks to fully tricked-out MDT ACC chassis, and the hits are the hits.

    That said, a few patterns hold up:

    • For a shooter just starting out, the factory stock is almost always good enough to learn the game. Spend the chassis money on glass and ammo testing first.
    • For a shooter who wants maximum adjustability and a future-proof platform, a chassis is the better long-term investment, especially if you anticipate swapping barreled actions over time.
    • For a shooter who wants the lightest, most traditional setup, a quality laminate or composite stock — properly bedded and pillared — is hard to beat.

    Action Screw Torque: The Setting Most Shooters Get Wrong

    Action screw torque is the clamping force holding the barreled action into the stock or chassis. Two screws (sometimes three on long actions) thread up through the bottom metal, through the stock or chassis, and into the receiver. The torque value on those screws controls how the action seats, how stress is distributed across the receiver, and ultimately how the barrel vibrates when you pull the trigger.

    Too loose and the action shifts under recoil and handling. Group sizes open up, zero drifts, and you'll chase fliers all day. Too tight and you over-stress the receiver, distort the action, and can actually pinch the bolt enough to feel rough cycling. You'll also crush wood fibers in a non-pillared stock, which permanently changes the bedding surface.

    The sweet spot is rifle-specific, ammunition-specific, and sometimes even stock-specific. There is no single right number.

    Why the CZ 457 Is the Poster Child for Torque Sensitivity

    The CZ 457 is one of the most popular rifles in Long Gong, and for good reason — it's accurate, affordable, and well-supported by the aftermarket. It is also famously sensitive to action screw torque.

    The factory stock is wood (or polymer on lower trims), the inletting is decent but not precise, and the receiver is a relatively light forging. Tighten the action screws to the upper end of typical centerfire torque values — 45 or 55 inch-pounds — and you will almost certainly see groups open up. Many CZ 457 shooters find their best groups somewhere between 15 and 35 inch-pounds, with some rifles preferring as low as 12 and others happiest up near that 35 ceiling. The factory recommendation lives in the lower half of that range for a reason.

    What's happening mechanically: the CZ receiver is thin enough that excessive clamping force flexes it slightly, and the wood stock compresses unevenly under the bottom metal. Both effects move the barreled action around relative to where it sat the last time you pulled the trigger. Drop the torque into the sweet spot and the receiver runs straight, the stock stops fighting you, and groups tighten up.

    Other Rifles, Other Numbers

    This is not unique to CZ. It's just more pronounced.

    RifleTypical Torque Window
    CZ 457 (factory wood/poly stock)12–35 in-lb
    Tikka T1x (factory or chassis)35–45 in-lb
    Vudoo V-22 (precision chassis, V-block)35–45 in-lb (front and rear)
    Anschutz 54 / 1700 series25–35 in-lb
    Bergara B-14R (Rem 700 footprint)35–55 in-lb

    These are starting points, not gospel. The only way to know what your rifle wants is to test.

    How to Run a Torque Test

    This is a half-day project and one of the highest-return things you can do for your rifle.

    1. Get a real inch-pound torque wrench. The Wheeler FAT wrench is the popular budget choice. Whatever you use, make sure it's reading in inch-pounds (not foot-pounds — wrong unit, very different number).
    2. Pick one consistent ammunition lot for the entire test. Different lots throw off the data.
    3. Pick three or four torque values that bracket what you think the sweet spot is. For a CZ 457, that might be 15, 22, 28, and 35 inch-pounds. For a Tikka, 25, 35, 45, and 55.
    4. Shoot three five-shot groups at each torque value, at 50 or 100 yards depending on your zero range. Same target, same rest, same shooter, same conditions if possible. Document carefully.
    5. Re-torque between every group set, in the same order — front screw first, then rear, or whatever order matches your manufacturer's recommendation. Consistency in the process matters as much as consistency in the value.
    6. Measure groups and look for the value that produces the smallest average, not the smallest single group. One lucky group at the wrong torque can mislead you.

    Once you find your number, write it down. Stick a piece of tape inside your case with the torque value, the screw order, and the ammo lot you tuned with. Re-check it every few hundred rounds — torque can creep, especially in stocks without pillars.

    Bedding and Pillars: Why They Make Rifles More Accurate

    Bedding and pillars exist to solve the same fundamental problem: the barreled action needs to return to exactly the same position relative to the stock every single time the action screws are torqued. Any movement, compression, or distortion in that interface translates directly to point-of-impact shift downrange.

    What Pillars Are

    Pillars are short cylinders — usually aluminum, sometimes steel — that are bedded vertically into the stock where the action screws pass through. They span from just under the action down to the surface where the bottom metal contacts the stock.

    When you torque the action screws, the clamping force passes through the pillars instead of through the wood or composite material of the stock. The pillars don't compress. The wood underneath them can't be crushed because the pillars are taking the load. That means:

    • You can torque to your tested value and know the action is sitting at the same height every time.
    • The stock material doesn't slowly compress over hundreds of round cycles and drift your zero.
    • You can confidently use higher torque values without crushing the stock.

    Pillars are most important in wood and laminate stocks, where compression is the biggest enemy. Some composite stocks (Manners, McMillan) come pillared from the factory. Many factory wood stocks don't.

    What Bedding Is

    Bedding is the process of pouring a two-part epoxy compound — Devcon, Marine-Tex, Acraglas, Pro-Bed, or similar — into the action inlet of the stock, then setting the action into the wet epoxy with release agent applied so it cures around the action without sticking to it. When cured and removed, the action has its own custom-fit cradle in the stock with no voids, no high spots, and full contact across every surface that should be touching.

    A properly bedded action seats into one — and only one — position. There is no slop, no rocking, no flex. Stress is distributed evenly along the recoil lug, the tang, and the action body. When you torque the screws, the clamping force has nowhere to deform anything because everything is already in perfect contact.

    How Bedding and Pillars Improve Accuracy

    Mechanical precision in a rifle is mostly about consistency. The barreled action vibrates in a complex pattern every time the trigger breaks. As long as that vibration pattern is the same shot to shot, the bullets go to the same place. The moment anything in the action-to-stock interface changes — a wood fiber compresses a little more on this shot than the last, a void in the inletting lets the recoil lug shift forward two thousandths under recoil, a screw torque value drifts because the stock crushed slightly — the harmonic pattern changes and the bullet goes somewhere it didn't before.

    Pillars eliminate compression at the screw-hole interface. Bedding eliminates voids, high spots, and uneven contact across the entire action footprint. Together they lock the barreled action into a single, repeatable mechanical position, which means the barrel does the same dance every time the firing pin falls. That's accuracy.

    You will often see groups tighten by 20–40% after a proper bedding and pillar job on a previously unbedded factory stock. The rifle didn't suddenly become better — it just stopped randomizing its own answer.

    When to Pillar, When to Bed, When to Do Both

    Pillar only is the right call when:

    • You have a factory wood or laminate stock that's otherwise inletted reasonably well.
    • You want a simple, lower-cost upgrade that you (or a smith) can do in an evening.
    • You're not chasing the last 10% of mechanical precision — you just want consistent torque and to stop crushing your stock.

    Bed only is rare. Bedding without pillars in a wood stock leaves the screw-hole compression problem unsolved, and the bedding work itself will eventually be compromised by that compression. The two techniques really go together.

    Pillar and bed is the right call when:

    • You're building a serious precision rifle and want every mechanical variable nailed down.
    • You have a custom or aftermarket stock that arrived with pillars but no bedding (common with Boyds and similar).
    • You're rescuing a factory stock with sloppy inletting — voids, uneven contact, visible gaps under the recoil lug.

    Neither is the right call when:

    • You're running a quality chassis with a precision V-block or machined inlet. The chassis is doing the work bedding would do, and pillars are unnecessary because the chassis itself doesn't compress.

    That said, some shooters bed the action into a chassis anyway for the absolute tightest fit. It's diminishing returns territory, but it's not wrong.

    Putting It Together

    A Long Gong rifle that prints small groups, holds zero across range trips, and lets you focus on wind and trigger comes from a stack of small decisions, each one nudging the variance down:

    • Pick the platform that fits your shooting — stock for traditional feel and light weight, chassis for adjustability and modularity. Either can shoot.
    • Run a real torque test with a real inch-pound wrench. Find your rifle's number. Write it down. Re-check it periodically.
    • If you're in a stock, install pillars. This is the single highest-return mechanical upgrade for most factory rimfire rifles.
    • Bed the action if you want maximum precision, if your inletting is sloppy, or if you're already taking the action out to install pillars. Doing them together is more efficient than doing them separately.
    • If you're in a chassis, verify the V-block or inlet is making clean contact with the action. Use the manufacturer's recommended torque as a starting point and test from there.

    None of this is magic. All of it is repeatable. The shooter who tunes their rifle once and then spends the next thousand rounds learning the wind will beat the shooter who buys a new stock every six months and never figures out what their action screws want.

    We'll see you on the gong.

    Have questions or want to share what worked on your rifle? Reach out through the Texas Long Gong website or talk to any of us at the next match. The community is the point.

    Share this article

    Community rating

    Be the first to rate

    Comments on Stocks, Chassis, Torque, and Bedding

    Loading…