← Back to Knowledge Base

    ★ .22LR Knowledge Base

    Do You Need a Threaded Muzzle on a Precision .22LR Barrel?

    By Joe Eldridge

    © Property of Texas Long Gong

    You are welcome to share a link to this article or link back to it from your own site. Please do not copy, republish, or rehost the article in whole or in part on another site. Backlinks are encouraged; lift-and-shift is not permitted.

    One of the questions that comes up almost every time a new shooter orders a precision .22LR — a Vudoo, an RimX, a CZ 457 MTR, an Anschutz, a Bergara B-14R, or a custom build on a Bartlein, Benchmark, Shilen, or IBI blank — is whether to spec the barrel with a threaded muzzle. Sometimes 1/2"-28 threads are standard. Sometimes they are a $75 add-on. Either way, it is a choice that feels small at the order screen and gets considerably bigger the first time you read a forum thread about muzzle damage. The honest answer is that you almost certainly do not need a threaded muzzle to shoot a .22LR well at distance — and there is a real and measurable risk that comes with threading a thin rimfire barrel. Here's a walkthrough of the trade-off, the engineering, and where tuners and suppressors actually fit into a precision rimfire setup.

    Why Precision Rimfire Barrels Are Different From Centerfire

    The first thing to understand is that a .22LR precision barrel does not have a lot of metal to give up. Common contours in the precision rimfire world include .920" bull, .860" medium-heavy, and the very common factory profiles around .860"–.870" seen on CZ 457 MTR, Vudoo, and Tikka T1x match barrels. Some sporter-contour rifles taper down even further — the CZ 457 base rifle and the Ruger Precision Rimfire both come in at well under .700" at the muzzle.

    For comparison, a .22LR bore is only .222" land-to-land. That means even on a heavy .860" barrel, the wall thickness at the muzzle is roughly .319" all the way around — and that is the material that has to absorb both the harmonics of the shot and the physical stress of a thread-cutting operation. On a skinnier contour, you're working with even less.

    Now compare that to a centerfire PRS barrel: a .300" bore with a 1.250" contour has more than four times the wall thickness at the muzzle. Centerfire shooters thread muzzles routinely with no measurable accuracy loss. Rimfire is not the same animal.

    What Threading Actually Removes

    A 1/2"-28 thread requires a major diameter of about .500" — that is the outer diameter of the threaded section. Cutting threads on a .860" contour barrel means the gunsmith has to turn the outside of the muzzle down from .860" to roughly .500" before any threads are cut. That is approximately .180" of material removed off the diameter, or about .090" off the wall thickness at the muzzle.

    If your barrel happened to be a sporter contour that was already only .560" or .600" at the muzzle, the gunsmith is turning it down to .500" and then cutting threads into what is left. There is almost nothing between the bore and the outside of the barrel at that point.

    The Civil War's review of a True Precision threaded rimfire barrel notes the upgrade as "Threaded for 1/2×28 Suppressors and other muzzle devices" — a feature presented as a clear positive. And for a Ruger 10/22 plinker, it is. But "plinking at 50 yards with a suppressor" and "holding a vertical waterline at 300 yards on a 12-inch gong" are two completely different jobs, and the second one is unforgiving of anything that disturbs the way the bullet exits the barrel.

    The Muzzle Opens Up — And It's Measurable

    This is the part that does not get talked about enough. When you turn the outside of a barrel down and then cut threads into it, you are relieving stress in the steel. Barrel steel is under residual stress from the manufacturing process — drilling, reaming, button-rifling or cut-rifling, and contouring all impart stress that the steel "remembers." When you remove material, the steel relaxes, and the bore at that point can change dimensions slightly.

    A frequently cited Rimfire Central thread documents exactly this. A gunsmith inspected a 10/22 barrel that had been turned down from .90" to .50" at the muzzle and then threaded, and his measurement showed that the last 1/2" of the bore opened up in diameter by .0003". That is three ten-thousandths of an inch. It sounds tiny, and in absolute terms it is — but the .22LR bullet diameter is only .2255", and the bullet's contact with the bore at the muzzle is the last thing that influences its flight before it is on its own. A bore that opens up at the muzzle is the opposite of what a precision rimfire barrel is supposed to do.

    A separate Rimfire Central thread on .22LR barrel length and accuracy points out the convention going the other direction: a good rimfire barrel is made with the bore tighter at the muzzle end. High-end aftermarket barrels are hand-lapped with a deliberate muzzle choke — the bore is a fraction of a thousandth tighter at the muzzle than at the chamber. The same writer notes that Anschutz historically achieved this by leaving a knob at the muzzle which tends to restrict the bore from getting larger. Cutting that knob off — or turning it down to thread — works directly against the design intent.

    This is not a fringe opinion. KIDD Innovative Design, who builds some of the most respected 10/22 barrels in the country, was asked directly about the accuracy impact of threading. Their answer was about as direct as a manufacturer ever is on the record: "For ultimate accuracy we don't recommend muzzle threading or fluting. But both features are super cool." Translation — it is a trade-off, and they know it.

    The Crown Is Everything

    The crown is the very last point of contact between the barrel and the bullet. If gases escape unevenly around the bullet base as it exits — because the crown is asymmetric, nicked, or damaged — the bullet gets a tiny lateral push at the worst possible moment. That push shows up as a flier or, worse, as a consistent low-grade dispersion that the shooter spends weeks blaming on ammo or wind.

    A correctly threaded barrel must be recrowned after the threading operation. The factory crown is usually destroyed in the process. Most precision-focused gunsmiths know this and will recess-cut a fresh 11-degree or 45-degree crown inside the threaded section so that the actual crown sits behind the threads and is protected by them. This is how the better factory threaded barrels — Anschutz AV, KIDD, Vudoo, the Ruger Precision Rimfire — are done.

    The problem is that not every threading job out there is done by a precision-focused smith. A general gunsmith who threads centerfire barrels all day may not appreciate how much more sensitive a thin rimfire muzzle is. And if you then screw a thread protector or a muzzle device onto that crown, you have introduced one more interface that can shift, can be over-torqued, or can land slightly out of square — and every one of those things will show up on paper at 300 yards.

    What About Tuners? Almost All of Them Clamp On

    This is where a lot of new precision rimfire shooters get confused. They have heard that barrel tuners help with vertical dispersion in rimfire — and they do, when paired with good ammo — and they assume that means they need a threaded muzzle to attach one. They don't. The vast majority of rimfire-specific tuners are clamp-on, not threaded.

    Here are the names that come up the most in long-gong, NRL22X, and rimfire benchrest circles:

    • Harrell's Precision Rimfire Tuner — clamp-on, slides over the muzzle and tightens with set screws. Around $175. The de facto standard in rimfire benchrest.
    • Bukys Tuner — clamp-on, very popular with PRS-style rimfire competitors.
    • PDT (Particle Damping Technology) by Ezell — Ezell Custom Rifles explicitly notes that the rimfire version clamps on like a Harrell's and can be bored to your barrel diameter.
    • ABRA tuners — clamp-on, popular in benchrest.

    As one Rimfire Central contributor summarized in a tuner discussion: "rimfire tuners, which, by and large are all slip fit with clamps and extend out past the muzzle. Not much muzzle blast to require a threaded operation."

    There is a clear engineering reason that the rimfire world settled on clamp-on. As one experienced benchrest builder explained in the same forum: "You wouldn't thread a barrel blank because a good rimfire BR gunsmith doesn't know where the muzzle is going to be located until after he slugs it." High-end rimfire smiths slug the bore looking for the tight spot, then cut the barrel at that point — meaning the final muzzle location is determined after the barrel is in hand, not before. Threading commits you to a length and a muzzle location before that decision can be made.

    The clamp-on design also lets the shooter remove the tuner without unscrewing anything from the barrel — important because the tuner setting itself is often the variable being adjusted in a tuning session, and you do not want to introduce a "did I torque the thread protector the same way today" question on top of it.

    If you have already had your barrel threaded and you want to run a Harrell's-style clamp-on tuner, you have two options: install a snug thread protector under the tuner so the tuner clamps on the protector rather than directly on the bare threads, or buy one of the threaded tuner inserts that companies like Harrell's now sell specifically for this scenario. Harrell's lists a dedicated rimfire–air rifle tuner plug that slips inside the tuner for threaded barrels.

    When You Might Want a Threaded Muzzle

    The one defensible reason to thread a precision .22LR muzzle is if you plan to run a suppressor. But before you make a permanent change to the barrel for that reason, be honest about how often suppressors actually show up on the firing line at a precision rimfire match. Some shooters use them. Very few do. A suppressor really has no place in serious precision rimfire — the reasons are covered in the FAQ section below, but the short version is that a suppressor functions like an uncontrolled tuner whose weight changes as it fouls, and it makes match scoring genuinely difficult for anyone trying to track when each shot is fired.

    For general practice, plinking, and pest control, a rimfire suppressor is one of the most enjoyable accessories you can own — subsonic match ammo is already below the sound barrier, so there is no supersonic crack to worry about, and the can reduces the muzzle report to something close to a pellet rifle. If that is your use case, factory-threaded match barrels are the right answer. Anschutz AV, Vudoo, RimX, KIDD, the Ruger Precision Rimfire, and most of the modern precision rimfire offerings come with factory threads done by the manufacturer who built the barrel — meaning the threads were cut as part of the design rather than as an aftermarket modification to a finished barrel. The crown is recessed back inside the threads, the bore was measured and accounted for, and you are not going to see the muzzle-opening problem that comes from turning down and threading a barrel that was finished without threads in mind.

    What you should avoid is threading an existing match barrel after the fact for the option of running a can someday. The risk-to-reward is poor — you are trading measurable bore consistency for an accessory that most precision rimfire shooters do not actually use.

    What If You Already Have a Threaded Barrel and It Shoots Fine?

    Then leave it alone. The point of this article is not that threaded barrels can't shoot — they obviously can, and many do — but that the threading operation introduces risk that is not present in an unthreaded barrel. If your rifle is grouping where you want it, you are not losing anything by running it as-is, with or without a thread protector.

    A few practical notes if you are running a threaded barrel. Keep the thread protector torqued consistently if you shoot without a suppressor or tuner. Several shooters report that the thread protector ends up acting as part of the crown, and changes in how it sits can shift point of impact. As one shooter on Rimfire Central put it: "My conclusion the thread protector is acting as the crown. And if there is any airpocket on that tp face it goofs up thr accuracy." Snug, square, consistent. Don't switch back and forth between bare threads, thread protector, and suppressor mid-string — pick a configuration and zero on it. And if you run a tuner, run it with the same thread protector arrangement underneath it every time.

    FAQ — Suppressors and Precision Rimfire

    Doesn't a suppressor act as a tuner anyway, since it adds mass to the muzzle?

    Yes — and this is part of the problem, not a feature. A suppressor is a heavy weight hanging off the end of the barrel, and it absolutely shifts the barrel's harmonics and produces a "tune." The catch is that you do not get to control where that tune lands. With a Harrell's, Bukys, or PDT clamp-on tuner, you can dial position in measured increments and find the node for your specific lot of ammo. With a suppressor, you get whatever node the can's mass and length happen to put you at, and you have no adjustment available.

    But if the can tunes the rifle, isn't that a free upgrade?

    Only if it stays the same weight forever — and it doesn't. A .22LR suppressor accumulates significant carbon, lead, and unburned powder fouling over its service life. The mass at the muzzle grows over time, the harmonic node moves with it, and your tune drifts. Your point of impact drifts with it. You can be zeroed perfectly at the start of a match and find yourself walking shots low or high by the back half of the day, and you will not know whether to blame conditions, ammo, or the can. With a real tuner, the weight is fixed and the variable is one thing you actually control. With a suppressor, the weight is the variable, and you do not.

    How much can the point of impact really shift?

    Enough to matter at 300 yards. A few ounces of accumulated fouling at the very end of the barrel will move the harmonic node and change where the bullet exits in the barrel's whip cycle. On a target where a four-inch group is the difference between cleaning the match and going home, a variable you cannot see or measure is not a variable you want in the system.

    What about match scoring with a suppressed rifle?

    This is the one that does not come up until you have actually tried to keep score for a suppressed shooter. With an unsuppressed rifle, the report tells you when the shot broke — and the scorekeeper, RO, or spotter can sync the timing of an impact or a splash with the audible shot. With a suppressed rifle, the only way to know a shot was fired is to be watching the muzzle. Unless the scorekeeper is hyper-focused on the muzzle for every single shot, it is genuinely hard to tell when the shot was squeezed. That is a minor friction in casual practice and a real problem in a competitive match where the scorekeeper is tracking impacts on multiple targets and trying to attribute hits and misses correctly.

    So when is a suppressor the right call?

    For general practice, plinking, and pest control — it is hard to beat, and a good can transforms a .22LR into one of the most enjoyable rifles you will ever shoot. For competitive precision rimfire, it has very little place. Some shooters do run them, but the combination of a shifting tune, scoring difficulty, and the fact that the can occupies the muzzle real estate where a real tuner would otherwise live means the precision crowd has largely settled on bare or thread-protected muzzles with clamp-on tuners.

    Quick-Reference Checklist

    • Want a suppressor? Order a factory-threaded match barrel from the manufacturer. Do not have an existing match barrel threaded after the fact.
    • Want a tuner? Skip the threads — clamp-on tuners (Harrell's, Bukys, PDT, ABRA) are the precision rimfire standard.
    • Want maximum accuracy and no muzzle accessories? Unthreaded barrel, factory crown. Nothing to torque, nothing to wear, nothing to shift.
    • Already have a threaded barrel that shoots well? Leave it alone. Keep the muzzle interface consistent — same thread protector, same torque, every time.
    • Threading an existing match barrel? Only with a smith who specializes in precision rimfire, and only because you have a specific suppressor in hand. Not "to keep options open."
    • Running a suppressor in a match? Know that you are giving up a real tuner, accepting a drifting tune as it fouls, and making life harder on the scorekeeper.

    The barrel is the single most important component of a precision .22LR. The muzzle is the single most important inch of the barrel. There is no reason to introduce a stress-relief cut and an additional mechanical interface to that inch of barrel unless you are getting something concrete in return — and "keeping my options open" is not concrete enough to justify it.

    Share this article

    Community rating

    Be the first to rate

    Comments on Do You Need a Threaded Muzzle on a Precision .22LR Barrel?

    Loading…